ELCON PFC1500 Charger 1.5kW, 24-120VDC

ELCON PFC1500 Charger 1.5kW, 24-120VDC

$875.00

Contact Us for Availability

Maximum number of characters: 25

Maximum number of characters: 50

* Required Fields

PLEASE CONTACT US FOR AVAILABILTY PRIOR TO ORDERING. ELCON IS TRANSITIONING TO UHF CHARGERS, SO PFC CHARGERS MAY BECOME UNAVAILBLE AT ANY TIME.

These waterproof ElCon Chargers are true power factor correction chargers capable of being programmed for just about any battery chemistry. This allows you to have the optimal charging algorithm for your particular pack of batteries whether you are using AGM, Gel, Flooded SLA, Ni-Cad, NiMH, Lithium or any other rechargeable battery that may come on to the market in the future.

Please note: ElCon chargers are not user programmable. They must be programmed at the factory for your specific need. If you should decide after receiving the charger that you would like to have it reprogrammed for a different application, the charger must be sent back to Elecrtic Motorsport at your own expense. There is a reprogramming fee of $100 minimum and a 2-3 week wait.

Advantages

-Internal integrated PFC, no pollution to electric network, protect shocking on electric network from heavy current.

-Wide input voltage range AC85V~AC265V available for worldwide requirements, convenient for electric-network fluctuation and vehicles exportation.

-High with 93% above efficiency while only about 80% efficiency the traditional chargers can meet.

-Intelligent temperature compensation function in the charging process, preventing the damage to battery caused by charge-off or charge due, greatly extending the lifespan of the battery.

-Fully-sealed and water-proof, protecTCCH-192-06tion class IP65. Shock resistance treatment made inside makes vibration proof level up to SAEJ1378 that can fully meet the standard of automobile appliance usage.

-Available for various kinds batteries like Lead-Acid, LiFePO4 Battery etc., Flexible and programmable of the charging module. Memory to store 10 unique algorithms with ability to switch between algorithms.

-Available with CAN communication interface for BMS-controlled charging.

Specifications

Output Power Voltage Range Input Voltage
1.5kW 48V 18amp 24-67VDC 110VAC - Dual 220VAC
1.5kW 72V 12amp 60-90VDC
1.5kW 96V 10amp 72-120VDC

 

Spec
Model
Output Voltage
-Nominal 
Output Voltage
-Maximum
230vac
Output Current
-Maximum
115vac
TCCH-24-40
24V
34V
40A
TCCH-36-33
36V
51V
33A
TCCH-48-25
48V
68V
25A
TCCH-60-20
60V
85V
20A
TCCH-72-16
72V
102V
16A
TCCH-96-12
96V
136V
12A
TCCH-120-10
120V
170V
10A
TCCH-144-08
144V
203V
8A
TCCH-156-07
156V
217V
7A
TCCH-192-06
192V
258V
6.2A
TCCH-240-05 240V 340V 5A

Technical Features

AC Input Voltage Range
AC85V~AC265V
AC Input Frequency
45~65 Hz
AC Power Factor
≥0.98
Full Load Efficiency
≥93％
Mechanical Shock &
Vibration Resistance Level
Conformance to
SAEJ1378 Standard
Environmental Enclosure
IP65
Operating Temperature
-40℃～+55℃
Storage Temperature
-40℃～+100℃
Mechanical Dimensions
352mm×175mm×139mm
Net Weight
6.33kg

LED Indicator

Red-Green flash 
(one second interval)
Battery Disconnected
Red flash 
(three seconds interval)
Repair Battery
Red flash 
(one second interval)
<80% Charge Indicator
Yellow flash 
(one second interval)
>80% Charge Indicator
Green flash 
(one second interval)
100% Charge Indicator
 
Protection Features

1. Thermal Self-Protection: When the internal temperature of the charger exceeds 75℃, the charging current will reduce automatically. If exceeds 85℃, the charger will shutdown protectively. When the internal temperature drops, it will resume charging automatically.
2. Short-circuit Protection: When the charger encounters nexpected short circuit across the output, charging will automatically stop. When fault removes, the charger will re-start in 10 seconds.
3. Reverse Connection Protection: When the battery is polarity reversed, the charger will disconnect the internal circuit and the battery, the charging will stop and avoid been damaged.
4. Input Low-voltage Protection: When the input AC Voltage is lower than 85V, the charger will shutdown protectively and automatically resume working after the voltage is normal again.

Choice of Charging Curve (curve 1~10) 

1. The LED will flash red several times when AC is first connected, then the LED will flash green once. The number of red flashes denotes the present curve (e.g. If the red flashes three times, it means the present curve is curve 3).
2. To choose another curve, please cut off the power supply first, then unpeel the label, pressing the button while connecting the power. If you want to choose curve 3, release the button after the 3rd LED Flash. Now the selected curve (e.g. curve 3) will be recorded in memory. 
 
Alarms
 
 
LED Flashing Sequence（One Cycle）
Indication
1
R G _ _ _ _ _ _
Wrong Battery
2
R G R _ _ _ _ _
Overcharged
3
R G R G _ _ _ _
Battery Overheated
4
R G R G R _ _ _
Incorrect AC Input Voltage
5
R G R G R G _ _
External Thermal Sensor Fault
6
R G R G R G R _
Communication Interface Fault
7
G R _ _ _ _ _ _
Charger Overheated
8
G R G _ _ _ _ _
Charger Relay Fault；Repair
9
G R G R _ _ _ _
Charger Fault; Repair

 

 

 

 

 

 

 
 
 

Note: 
1. R—red    G—green
2. “_” denotes one second stop
3. Above LED flashing sequence is one cycle, the LED will flash repeatedly when in fault.
 
Installation & Safety Instructions
 
1. Preferably the charger should be installed in the horizontal position or installed vertically along radiation tooth. A space of 5cm around the radiation tooth should be open to ensure airflow.
2. Ensure all heat dissipating parts are not obstructed to avoid overheating. Do not put the battery charger near any heat sources. Make sure that free space around the charger is enough to provide adequate ventilation & easy cable socket access.
3. Ensure the consistency between the alternating supply voltage and the allowable voltage input of the charger, please approach a retailer or local Power Utility for enquiry.
4. For safety and electromagnetic compatibility, the battery charger has a 3-prong plug that apply tothe socket withgrounded outlet.
5. If you are using an extension cord for alternating current power supply, make sure that it is affordable to the maximum input current.
6. The voltage-drop between the charger and connection wire of the battery should be as less than 1% of the battery voltage as it can. Otherwise, it affects charging effect possibly. Meanwhile, the diameter of the wire should satisfy the output current value.
7. The thermal compensation probe for the battery voltage must be placed in the area of the highest battery temperature, such as between 2 batteries near the center of the pack.
8. If the charger does not work correctly or if it has been damaged, unplug it immediately from the supply socket, from the battery and contact a retailer.
9. Do not try to service the charger yourself. Opening the cover may expose you to shock or other hazards.
10. To avoid damaging the power cord, do not put anything on it or place it where it will be walked on. If the cord becomes damaged or frayed, replace it immediately. 

 

Availability Contact Us for Availability
Country of Manufacture China

For assistance with selecting the right components for your project, please use the appropriate form:

LVW Land Vehicle Worksheet
MCW Marine Craft Worksheet

video title

video content
Scrollsearch Icon
You have no items in your shopping cart.